The wall mount kit is not in the box
The B-Air Firtana 20" is sold as a floor fan with a folding stand, and the supplied information says the stand can be wall-mounted only with a wall mounting kit that is not included. That single fact sets the order of work: buy or source a compatible kit first, then plan placement, then mount. The supplied information does not specify a kit model, fastener type, or load rating, so choose a kit rated for the fan's weight and follow the kit maker's instructions rather than guessing at hardware.
The fan itself gives you useful numbers for planning: 24" x 22.3" x 6" overall dimensions and a net weight of 12 lbs. Those are the figures to check against your wall space and against the kit's stated capacity before you commit to a spot.
B-Air Firtana 20" numbers that drive the placement decision
- B-Air 20" High Velocity Floor Fan: wall mount, 3-speed, pivoting: Dimensions: 24" x 22.3" x 6"; net weight 12 lbs Use these to confirm wall clearance and to match a mounting kit to the fan's size and weight.

B-Air 20" High Velocity Floor Fan: wall mount, 3-speed, pivoting - B-Air 20" High Velocity Floor Fan: wall mount, 3-speed, pivoting: Wall mounting kit not included You must supply the kit; the fan cannot be hung from the stand alone.
- B-Air 20" High Velocity Floor Fan: wall mount, 3-speed, pivoting: Pivoting fan head The head angle can be adjusted after mounting, so exact height matters less than a clear swing path.
- B-Air 20" High Velocity Floor Fan: wall mount, 3-speed, pivoting: Airflow 4650 CFM; speeds High 1507 RPM, Medium 1360 RPM, Low 1253 RPM This is a high-output fan, so aim it across the room rather than at people sitting close to the wall.
A supported sequence for mounting the Firtana 20"
The supplied information does not include step-by-step mounting instructions, so this sequence covers only the decisions the catalog evidence supports. Fastener selection and wall preparation belong to your mounting kit's instructions.
- 1. Confirm the kit and the wall: The stand folds for storage or can be wall-mounted with a kit that is not included. Get the kit in hand before drilling, and check that the wall structure suits the kit you chose.
- 2. Reserve the footprint: Allow for the 24" x 22.3" x 6" body plus room for the pivoting head to swing. Keep the small-grid guard clear of curtains, shelving, and anything that could block intake or output.
- 3. Pick a height with the airflow in mind: The supplied information gives no recommended mounting height. A practical approach is to set the fan so its pivoting head can aim across the room at the height where people work or sit, then fine-tune the angle after mounting.
- 4. Plan the cord run: The cord is 5 feet, 18 AWG, on a 120V, 1.35A, 157W fan. Check that a grounded outlet reaches the chosen spot without an extension cord crossing a walkway.
- 5. Set speed and angle after mounting: Start on Low (1253 RPM) and step up to Medium (1360 RPM) or High (1507 RPM) only if the room needs it. Adjust the pivoting head before you settle into a routine.
Height and aim: what the evidence can and cannot tell you
There is no manufacturer-recommended wall height in the supplied information, so treat any specific number as your own judgment rather than a B-Air instruction. What the record does support is the logic of the choice: the fan moves up to 4650 CFM, the head pivots, and the guard has small grid spacing to keep fingers and paws out. A high, wall-mounted position aimed slightly downward across a workshop or garage uses that airflow without blasting anyone at close range.
The 5-foot cord is the other hard constraint. On a wall, the outlet effectively becomes part of the placement plan. If the nearest outlet is farther than the cord allows, move the fan rather than stretching the run with an undersized extension cord.
Floor stand or wall mount: choosing for your space
- Floor stand: No kit needed. The folding stand and built-in handle make the 12 lb fan easy to move between rooms, and the 24" x 22.3" x 6" footprint sits on the floor.
- Wall mount: Frees floor space in tight areas, but requires a separately purchased mounting kit and a suitable wall. The pivoting head still lets you aim the airflow after installation.
Where the Firtana 20" fits and what to check before you drill
The catalog describes the fan for restaurants, home offices, garages, and music venues, and its all-metal housing and 1-year limited warranty suit a workmanlike installation. Before drilling, confirm three things: the mounting kit is rated for a 12 lb, 24" x 22.3" x 6" fan; the wall can accept that kit; and the outlet is within the 5-foot cord reach. The supplied information does not cover assembly steps, load limits, or safety ratings for wall mounting, so those details must come from the kit manufacturer and your own assessment of the wall.


