The room size difference is the whole decision
The Air King 50 CFM and 70 CFM Snap-In exhaust fans share the same WML Snap-In installation system, LED lamp, plastic damper, and ENERGY STAR certification. The meaningful difference is airflow and the room size each fan is rated to serve. The 50 CFM model is intended for bathrooms up to 45 sq. ft.; the 70 CFM model covers bathrooms up to 65 sq. ft. For other rooms, including powder rooms, the ratings extend to 65 sq. ft. and 85 sq. ft., respectively. If your bathroom is at or below 45 sq. ft., the 50 CFM fan meets the listed coverage. Above that, the 70 CFM model is the one rated for the job.
Coverage and airflow at a glance
- Air King 50 CFM Snap-In Exhaust Fan (ENERGY STAR® Certified, ceiling mounted, light, white): 50 CFM blower; for bathrooms up to 45 sq. ft.; for other rooms, including powder rooms, up to 65 sq. ft. Use this as the upper limit for a small full bath or a larger powder room.

Air King 50 CFM Snap-In Exhaust Fan (ENERGY STAR® Certified, ceiling mounted, light, white) - Air King 70 CFM Snap-In Exhaust Fan (ENERGY STAR® Certified, ceiling mounted, light, white): 70 CFM blower; for bathrooms up to 65 sq. ft.; for other rooms, including powder rooms, up to 85 sq. ft. Choose this when your bathroom exceeds the 50 CFM model's 45 sq. ft. bathroom rating.

Air King 70 CFM Snap-In Exhaust Fan (ENERGY STAR® Certified, ceiling mounted, light, white)
Noise: 0.8 sones versus 2.0 sones
The 50 CFM model is rated at 0.8 sones, which the catalog describes as barely audible. The 70 CFM model is rated at 2.0 sones and described as quiet. Both are low figures for a ceiling bath fan, but they are not the same experience. If the fan sits directly over a shower or near a bedroom wall, the 0.8-sone rating of the 50 CFM model is a real advantage. If your room requires the 70 CFM model's coverage, accept the higher 2.0-sone rating as the tradeoff for more airflow.
Side-by-side: what changes and what stays the same
- Airflow: 50 CFM versus 70 CFM.
- Bathroom coverage: Up to 45 sq. ft. versus up to 65 sq. ft.
- Other-room coverage: Up to 65 sq. ft. versus up to 85 sq. ft., including powder rooms.
- Noise rating: 0.8 sones versus 2.0 sones.
- Installation: Both use the WML Snap-In system: a bracket nails or screws to the ceiling joist, then the housing snaps into place.
- Wiring and ducting: Both include wire nuts and strain relief; connect wiring, install ducting, and fit the grill.
- Light: Both include an LED lamp that can be wired independently of the fan.
- Damper and housing: Both have a plastic damper against back drafts and a high-impact plastic housing that resists corrosion and rust.
- Certification: Both are ENERGY STAR certified and UL listed for installation over a tub or shower on a GFCI circuit.
Snap-In installation is identical on both models
Because both fans belong to the WML series, the installation sequence does not change with size. The included bracket attaches to the ceiling joist with nails or screws, the fan housing snaps into the bracket, and you finish by connecting the wiring with the supplied wire nuts and strain relief, installing the ducting, and fitting the grill. The catalog states that a bath fan installation can now be done in minutes. Neither record supplies a ceiling cutout dimension, housing height, or duct diameter, so confirm those measurements against your existing opening before ordering if you are replacing an older fan.
How to choose without oversizing
Measure the floor area of the room the fan serves, not the whole floor plan. If the result is 45 sq. ft. or less, the 50 CFM model is rated for that bathroom and gives you the quieter 0.8-sone operation. If the bathroom is between 45 and 65 sq. ft., the 70 CFM model is the one rated for the space. For a powder room, the same logic applies with the higher limits: up to 65 sq. ft. for the 50 CFM fan and up to 85 sq. ft. for the 70 CFM fan. There is no supplied guidance on pairing either fan with a particular duct run length, so keep ductwork as direct as your layout allows and verify local code requirements separately.



